VAZ 2101, 2102
1. Specifications
2. Operation and service
3. The engine
3.1. Features of the device
3.2. Possible malfunctions of the engine, their reason and elimination methods
3.3. Removal and engine installation
3.4. Engine dismantling
3.5. Engine assemblage
3.6. Bench tests of the engine
3.7. Engine check on the car
3.8. The block of cylinders
3.9. Pistons and rods
3.10. A cranked shaft and a flywheel
3.11. A head of cylinders and клапанный the mechanism
3.12. A camshaft and its drive
3.13. Cooling system
3.13.1. Features of the device
3.13.2. Check of level and liquid density in cooling system
3.13.3. Refuelling of system of cooling by a liquid
3.13.4. Adjustment of a tension of a belt of a drive of the pump
3.13.5. The pump of a cooling liquid
3.13.6. The thermostat
3.13.7. A radiator
3.14. Greasing system
4. Fuel system
5. Ignition system
6. Start and gymnastics system
7. Transmission
8. A running gear
9. A steering
10. Brake system
11. An electric equipment
12. A body
13. Features of repair
14. Appendices


7b94d386




3-13-5-nasos-okhlazhdayushhejj-zhidkosti.html

3.13.5. The pump of a cooling liquid

Longitudinal section of the pump of a cooling liquid

1 – the case;
2 – a cover;
3 – a nut of fastening of a cover of the pump;
4 – the fan;
5 – a pulley nave;
6 – an overlay;
7 – the platen;
8 – a pulley;
9 – the lock screw of the bearing;
10 – the bearing;
11 – an epiploon;
12 – крыльчатка

Напрессовка крыльчатки on the platen of the pump adaptation A.60430

1 – a support;

2 – the pump platen;

3 – a cover of the case of the pump;

4 – a glass;

5 – the adjusting screw

Dismantling

PERFORMANCE ORDER
1. Disconnect the case of the pump from a cover 2 (fig. the Longitudinal section of the pump of a cooling liquid see).
2. Fix a cover in a vice, using linings, and remove крыльчатку 2 from the platen stripper А.40026 (1 – stripper А.40026).
3. Remove a nave 2 pulleys of the fan from the platen by means of stripper А.40005/1/5 (1 – a cover of the case of the pump, 3 – stripper А.40005/1/5).
4. Turn out the lock screw 9 (fig. the Longitudinal section of the pump of a cooling liquid see) and take out the bearing with the pump platen.
5. Remove an epiploon 11 from a cover of 2 cases.

The control

PERFORMANCE ORDER
1. Check up an axial backlash in the bearing. It is necessary to do this operation necessarily if considerable noise of the pump is marked. The backlash should not exceed 0,13 mm at loading 49 Н (5 кгс). At the big backlash the bearing replace.
2. Between the pump and the block of cylinders at repair it is recommended to replace an epiploon of the pump and a lining.
3. Examine the case and a pump cover. Deformations or cracks on them are not supposed.

Assemblage

PERFORMANCE ORDER
1. Establish оправкой an epiploon, without supposing a warp, in a case cover.
2. Запрессуйте the bearing with the platen in a cover so that the nest of the lock screw has coincided with an aperture in a cover of the case of the pump.
3. Wrap the lock screw of the bearing and зачеканьте nest contours that the screw did not weaken.
4. Напрессуйте by means of adaptation A.60430 (fig. of Napressovka крыльчатки on the platen of the pump adaptation A.60430 see) on the platen a pulley nave, having sustained the size 84,4±0,1 mm.
5. Напрессуйте крыльчатку on the platen by means of adaptation A.60430, having provided a backlash between shovels крыльчатки and the case of the pump of 0,9-1,3 mm.
6. Collect the case of the pump with a cover, having established between them a lining.

«The previous page
3.13.4. Adjustment of a tension of a belt of a drive of the pump
The following page»
3.13.6. The thermostat