VAZ 2101, 2102
1. Specifications
2. Operation and service
3. The engine
3.1. Features of the device
3.2. Possible malfunctions of the engine, their reason and elimination methods
3.3. Removal and engine installation
3.4. Engine dismantling
3.5. Engine assemblage
3.6. Bench tests of the engine
3.7. Engine check on the car
3.8. The block of cylinders
3.9. Pistons and rods
3.10. A cranked shaft and a flywheel
3.11. A head of cylinders and клапанный the mechanism
3.12. A camshaft and its drive
3.13. Cooling system
3.14. Greasing system
4. Fuel system
5. Ignition system
6. Start and gymnastics system
7. Transmission
8. A running gear
9. A steering
10. Brake system
11. An electric equipment
12. A body
13. Features of repair
14. Appendices


7b94d386




3-3-snyatie-i-ustanovka-dvigatelya.html

3.3. Removal and engine installation

PERFORMANCE ORDER
1. Put the car on the lift or over a viewing ditch, establish an emphasis under forward wheels and will hang out the back bridge from one or two parties.
2. Remove a cowl, disconnect wires from the storage battery and from the knots of an electric equipment established on the engine. Remove the storage battery and подкапотную a lamp.

The prevention

Not to damage a radiator, turning the drain stopper, with the second key hold the union of the stopper which have been soldered in in a radiator. A stopper turn on face or накидным a key not to break a stopper side.


3. Merge a liquid from a radiator, the block of cylinders and a heater for what turn away a stopper on a left-hand side of the block of cylinders and on the bottom tank of a radiator, top рычажок managements of a heater shift to the right (it the heater crane opens) and remove stoppers from a broad tank and a radiator.
4. Remove a fan casing. Disconnect from the engine hoses of a supply and tap of a cooling liquid and remove a radiator together with the thermostat and hoses.
5. Remove the air filter, preliminary having disconnected from it hoses, having uncovered and a filtering element. Close the carburettor technological заглушкой.
6. Turn away a nut of fastening of a reception pipe of mufflers to a final collector.
7. Remove a transmission (subsection 7.2.2 see).
8. Disconnect from the engine draught of a drive throttle заслонки the carburettor and a cable of management air заслонкой.
9. Disconnect from the engine a hose of a supply of fuel and the hoses going to a heater.
10. Hang up on таль to traverse ТСО-3/379 and застропите the engine on the right side for скобу, established on a forward hairpin of fastening of a final collector, and on the left side – for an aperture of fastening of a casing of coupling.
11. Slightly pull a chain тали, turn away a nut of fastening of pillows 9 (fig. the Engine mount) a forward engine mount to a cross-beam of a forward suspension bracket see and take out the engine from a motor compartment.
12. Remove теплоизоляционный a guard of a starter and заборник hot air together with a bringing hose. Remove from the block of cylinders two lateral arms with pillows of a forward engine mount.
13. Turn away bolts of fastening of coupling and remove it.
14. Remove теплоизоляционный a guard of a starter and заборник hot air together with a bringing hose. Remove from the block of cylinders two lateral arms with pillows of a forward engine mount.
Turn away bolts of fastening of coupling and remove it.
15. Establish the engine on the car in sequence, return to removal. Special attention give to connection of the engine with a transmission: the primary shaft should precisely, without a warp, enter in шлицы a conducted disk of coupling.

«The previous page
3.2. Possible malfunctions of the engine, their reason and elimination methods
The following page»
3.4. Engine dismantling