VAZ 2101, 2102
1. Specifications
2. Operation and service
3. The engine
4. Fuel system
5. Ignition system
6. Start and gymnastics system
7. Transmission
8. A running gear
9. A steering
10. Brake system
10.1. Features of the device
10.2. Check and adjustment of brakes
10.2.1. Check of pipelines and connections
10.2.2. Adjustment of a free wheeling of a pedal of a brake
10.2.3. Adjustment of a lay brake
10.2.4. Check of working capacity of a regulator of pressure
10.2.5. Adjustment of position of a regulator of pressure
10.2.6. Removal of air from a hydrodrive of brakes
10.2.7. Backlash adjustment between колодками and a drum
10.3. An arm of pedals of coupling and a brake
10.4. The main cylinder
10.5. Forward brakes
10.6. Back brakes
10.7. A regulator of pressure of back brakes
10.8. A lay brake
10.9. Possible malfunctions of brakes, their reasons and elimination methods
11. An electric equipment
12. A body
13. Features of repair
14. Appendices


7b94d386 тв каналы для взрослых
buy cheap viagra usa





10-2-5-regulirovka-polozheniya-regulyatora-davleniya.html

10.2.5. Adjustment of position of a regulator of pressure

The scheme of installation of a regulator of pressure of back brakes and its adjustment

1, 2 - bolts of fastening of a regulator to an arm;
3 – a protective cap;
4 – торсионный the lever of a drive of a regulator;
5 – an arm of fastening of the lever to a body;
6 – the piston;
7 - draught of connection with an arm of a beam of the back bridge;
8 – an axis;
9 - the union of the pipeline for a supply of a brake liquid from the main cylinder;
10 – the union of the pipeline for tap of a brake liquid in wheel cylinders

Installation of the adaptation 67.7820.9518 for adjustment of a regulator of pressure of back brakes

1 – an arm of the lever of a drive of a regulator of pressure;

2 – the lever of a drive of a regulator of pressure of back wheels;

3 – the adaptation 67.7820.9518;

4 - draught of connection of the lever of a drive of a regulator of pressure with an arm of a beam of the back bridge


PERFORMANCE ORDER
1. If ослабли bolts, крепящие a regulator of pressure of back brakes adjust its position. For this purpose, having hung out a back axis of the car, ослабьте bolts 1 and 2 (fig. the Scheme of installation of a regulator of pressure of back brakes and its adjustment see) so that the regulator could be turned easily concerning a fastening arm.
2. Disconnect the lever 4 from draught 7 and fix on its end the adaptation 67.7820.9518 (fig. Installation of the adaptation 67.7820.9518 for adjustment of a regulator of pressure of back brakes see).
3. An adaptation core direct upwards, against the stop to a body. This most establishes distance of 140+5 mm between the end of the lever 4 (fig. the Scheme of installation of a regulator of pressure of back brakes and its adjustment see) and a body longeron.
4. Raise a protective rubber cap 3 and, turning a pressure regulator on bolts, achieve easy contact of the lever with the piston 6.
5. Keeping in this position a pressure regulator, tighten to the full bolts 1 and 2, then cover with greasing ДТ-1 an axis 8 and an acting part of the piston.
6. Establish into place a rubber cap.
7. Remove the adaptation 67.7820.9518 and connect the end of the lever to draught 7.

«The previous page
10.2.4. Check of working capacity of a regulator of pressure
The following page»
10.2.6. Removal of air from a hydrodrive of brakes