VAZ 2101, 2102
1. Specifications
2. Operation and service
3. The engine
4. Fuel system
5. Ignition system
6. Start and gymnastics system
7. Transmission
7.1. Coupling
7.2. A transmission
7.3. Kardannaja transfer
7.3.1. Features of the device
7.3.2. Removal and installation
7.3.3. Check of a technical condition without dismantling
7.3.4. Dismantling
7.3.5. Check of a technical condition
7.3.6. Assemblage
7.3.7. Balancing of shaft
7.3.8. Possible malfunctions карданной transfers
7.4. The back bridge
8. A running gear
9. A steering
10. Brake system
11. An electric equipment
12. A body
13. Features of repair
14. Appendices


7b94d386 спидминтон забава для шустрых.
Tk-1120 смотрите на kyoshop.ru.
Дизайн квартир пермь Обзор лучших дизайн, гидмаркет по материалам dizaynerperm.ru.
Выкуп авто дорого по материалам http://www.autostock.com.by.
Купить дубликат ву еще по теме.





7-3-8-vozmozhnye-neispravnosti-kardannojj-peredachi.html

7.3.8. Possible malfunctions карданной transfers

THE REASON
ELIMINATION METHOD
Knock in карданной to transfer at трогании from a place, at sharp dispersal or a gear change
Easing of a tightening of bolts and nuts of fastening elastic муфты and flanges карданных hinges Tighten nuts the moments specified in the appendix
The increased district backlash in шлицевом connection forward карданного a shaft Check up backlash size if it more than 0,30 mm, replace the worn out details
The increased backlash in bearings карданных hinges Repair hinges with replacement of the worn out details
Noise and vibration карданной transfers
Deformation карданных shaft Correct on a press or replace shaft
Discrepancy of assembly labels of a forward shaft and corresponding муфты Remove карданную transfer and achieve coincidence of the labels put at dismantling
Disbalance карданных shaft Check up balancing; at a disbalance exceeding 2,15 Нмм (220 гсмм), operate, as it is described in subsection 7.3.7.
Deterioration or damage of the aligning plug of a flange elastic муфты and an aligning ring of a secondary shaft of a transmission Replace a flange elastic муфты in gathering with the plug and an aligning ring of a secondary shaft
The raised backlash in the bearing of an intermediate support Replace the bearing
Damage of an intermediate support Replace a support
Easing of a tightening of nuts of fastening of a cross-beam to a car body Tighten nuts of fastening of a cross-beam
The raised backlash in bearings карданных hinges or jamming of hinges Repair hinges with replacement of the worn out details
Easing of a holder of an epiploon of a flange elastic муфты Draw in an epiploon and press out its holder; at greasing leak replace an epiploon
Easing of a nut of fastening of a plug forward карданного a shaft Disconnect a forward shaft from back and tighten a nut, then a nut зачеканьте
Insufficient greasing шлицевого connections Grease шлицевое connection by greasing ФИОЛ-1
Greasing leak
Easing of a holder of an epiploon of a flange elastic муфты, deterioration of consolidation Draw in an epiploon and press out its holder, the worn out epiploon replace
Damage or deterioration of epiploons карданных hinges Disassemble hinges and replace epiploons, if necessary, replace крестовину in gathering with bearings

The previous page
7.3.7. Balancing of shaft
The following page
7.4. The back bridge