VAZ 2101, 2102
1. Specifications
2. Operation and service
3. The engine
4. Fuel system
5. Ignition system
6. Start and gymnastics system
6.1. The storage battery
6.2. The generator
6.2.1. A technical characteristics
6.2.2. Control checks of the generator
6.2.3. Generator repair
6.2.3.1. Generator dismantling
6.2.3.2. Generator assemblage
6.2.3.3. Replacement щеткодержателя
6.2.3.4. Replacement of bearings of a rotor
6.2.3.5. Replacement of gates
6.2.3.6. The relay of a control lamp of a charge of the storage battery
6.2.4. A regulator of pressure РР–380
6.2.5. Possible malfunctions of the generator, their reason and elimination methods
6.3. A starter
7. Transmission
8. A running gear
9. A steering
10. Brake system
11. An electric equipment
12. A body
13. Features of repair
14. Appendices


7b94d386 It outsourcing offshore.
интернет-магазин для мыловаров.
Промышленный обогрев смотри здесь.
Продакшн студия по материалам сайта.
Где купить детоциклин: официальный сайт и цены.





6-2-3-remont-generatora.html

6.2.3. Generator repair

Generator details
1 – "a negative" brush;
2 – щеткодержатель;
3 – "a positive" brush;
4 – колодка the tip of a zero wire;
5 – isolating plugs of a contact bolt;
6 – выпрямительный the block;
7 – a contact bolt;
8 – статор;
9 – a rotor;
10 – an internal washer of fastening of the bearing;
11 – a cover from outside a drive;
12 – the fan in gathering with a pulley;
13 – an external washer of fastening of the bearing;
14 – the forward bearing of a rotor;
15 – a remote ring;
16 – a coupling bolt;
17 – поджимная the plug;
18 – a cover from outside contact rings;
19 – the buffer plug;
20 – the plug

PERFORMANCE ORDER
1. Clear and blow the generator the compressed air. Turn away the screw and remove щеткодержатель 2 with brushes.
2. Remove a pulley of the generator by means of the adaptation 67.7823.9504. For this purpose застопорьте a pulley the capture entering into the complete set of the adaptation, turn away a nut of fastening of a pulley and a stripper press a pulley. Remove шпонку and a conic washer of a pulley. The complete set of the adaptation 67.7823.9504 includes a usual stripper and capture. Last consists of two steel half rings which are put in a pulley stream. Half rings have the same section, as well as a belt of a drive of the generator. On the one hand they are connected шарнирно, and with another – are supplied by levers which are compressed by a hand at отворачивании nuts and pulley removal.
3. Turn away a nut of four coupling bolts 16 and disconnect a back cover 18 with статором 8 and выпрямительным the block 6 from a forward cover 11 with a rotor 9.
4. Take out a rotor with a remote ring from the bearing of a forward cover.
5. Turn away a nut of the screws connecting tips of gates with conclusions of a winding статора, take out from колодки 4 tip of the central conclusion of a winding статора and disconnect статор from a back cover.
6. Turn away a nut of a contact bolt 7 and take from a cover выпрямительный
The block 6.

«The previous page
6.2.2.6. Check of gates выпрямительного the block
The following page»
6.2.3.1. Generator dismantling