VAZ 2101, 2102
1. Specifications
2. Operation and service
3. The engine
4. Fuel system
5. Ignition system
6. Start and gymnastics system
7. Transmission
8. A running gear
8.1. A forward suspension bracket
8.1.1. A forward suspension bracket, wheels, tyres
8.1.2. Definition of a condition of details of a forward suspension bracket
8.1.3. Check and adjustment of corners of installation of forward wheels
8.1.4. Removal and installation of a forward suspension bracket
8.1.5. Dismantling and assemblage of knots of a suspension bracket
8.1.6. Check of a technical condition and repair
8.1.7. Replacement резинометаллических hinges of levers on the car
8.2. A back suspension bracket
8.3. Shock-absorbers
8.4. Possible malfunctions of a running gear, their reason and elimination methods
9. A steering
10. Brake system
11. An electric equipment
12. A body
13. Features of repair
14. Appendices


7b94d386 приема радиодеталей и технического серебра.
Реконструкция дачи читать далее.
миграционные услуги
Каррагинан купить в розницу по материалам сайта.
Смотри здесь tk-6115.





8-1-4-snyatie-i-ustanovka-perednejj-podveski.html

8.1.4. Removal and installation of a forward suspension bracket

PERFORMANCE ORDER
1. Establish the car on the lift or a viewing ditch; keeping key А.57070 the rod end for лыски, disconnect the top end of the shock-absorber and remove forward wheels.
2. Having unbent lock plates, turn away bolts of fastening of a support to an arm. Take a support aside and fix it so that it did not hang on hoses. Remove shock-absorbers with arms.
3. Disconnect the ends штангов the stabilizer of cross-section stability from the bottom levers of a suspension bracket.
4. A stripper 67.7801.9513 выпрессуйте fingers from apertures of levers also take steering draughts aside.
5. Insert the screw 2, adaptations 67.7828.9504, in an aperture of the top support of a spring of a suspension bracket, then from below put on a coil of a spring 1 and on the screw 2 basic plate 3 and fix it on a spring a clip. From below on the screw screw a nut so that the nut clamp has come into a nest of a plate 3. Rotating a key the screw 2, compress a spring of a suspension bracket before full unloading of levers of a suspension bracket.
6. Take out an axis of the top lever and disconnect it from a body. Disconnect an axis of the bottom lever from a cross-beam and remove knot of a suspension bracket from the car.
7. Remove a spring, smoothly having unloaded it, clean the adaptation and repeat operations for other knot of a suspension bracket.
The prevention

Removing suspension bracket knots, it is necessary to note quantity and an arrangement of washers between an axis of the bottom lever and a cross-beam, and also adjusting plates between a cross-beam and body longerons that, at installation of knots, to put these washers and plates on a former place.


8. Remove a mudguard of the engine and a stabilizer bar.
9. Supporting the engine траверсой А.70526 or талью, remove a cross-beam.
10. Establish knots and suspension bracket details in an order, the return to removal. Springs on forward and back suspension brackets establish the same groups (the group And is marked by a yellow paint, and group springs In – green). In exceptional cases, installation on a forward suspension bracket of springs of group is supposed And, and on back – springs of group of V.Esli on a forward suspension bracket group springs are established In on a back suspension bracket establish springs of the same group.
11. For the prevention of wrong distribution of efforts in резинометаллических hinges, the tightening of nuts and axes of levers is necessary for making in a following order:
      – Establish the car on an equal platform and put wheels in parallel a car axis;
      – Load the car with loading 320 кгс (four persons of 40 kg in a luggage carrier);
      – In these conditions, динамометрическим a key, tighten nuts of fastening of axes top, and then bottom levers and a nut of fastening of an axis of the bottom lever to a cross-beam.
12. Check up and adjust corners of installation of forward wheels.

«The previous page
8.1.3. Check and adjustment of corners of installation of forward wheels
The following page»
8.1.5. Dismantling and assemblage of knots of a suspension bracket