VAZ 2101, 2102
1. Specifications
2. Operation and service
3. The engine
4. Fuel system
5. Ignition system
6. Start and gymnastics system
7. Transmission
8. A running gear
9. A steering
9.1. Features of the device
9.2. Survey, check and steering adjustment
9.3. The steering mechanism
9.3.1. Removal and installation
9.3.2. Dismantling and assemblage картера the steering mechanism
9.3.3. Check and repair
9.4. Draughts and spherical hinges of a steering drive
9.5. An arm of the pendular lever
9.6. Possible malfunctions of a steering
10. Brake system
11. An electric equipment
12. A body
13. Features of repair
14. Appendices


7b94d386







9-3-rulevojj-mekhanizm.html

9.3. The steering mechanism

Steering details
1 – картер the steering mechanism;
2 – a fastening bolt картера the steering mechanism to a body;
3 – an adjusting washer;
4 – a flat washer;
5 – a nut;
6 – a spring washer;
7 – a bolt of fastening of a tip of a shaft of the steering mechanism on a shaft of a worm;
8 – a shaft sealant;
9 – the screw of fastening of a rubber sealant to a body;
10 – a shaft of the steering mechanism;
11 – a bolt of fastening of an arm of a shaft of the steering mechanism;
12 – an arm of a shaft of a steering;
13 – a steering wheel;
14 – a nut of fastening of a steering wheel

Installation of the steering mechanism on the car

1 – fastening bolts картера the steering mechanism to a body;
2 – a bolt of fastening of a shaft of a steering to a shaft of a worm;
3 – bolts of fastening of an arm of a shaft of a steering to a body;

4 – the plastic plug;
5 – an arm of fastening of a shaft of a steering;
6 – adjusting washers for maintenance соосности a shaft of a worm and a steering shaft


PERFORMANCE ORDER
1. Disconnect wires from the storage battery and uncover the signal switch, cautiously having unbent fingers at first one, then its other end from the bottom party.
2. Remove a steering wheel.
3. Remove both half of facing casing of a shaft of a steering.

The prevention

If it is necessary to remove only картер the steering mechanism, turn away bolts of fastening of an arm and a bolt, крепящий a steering shaft on a shaft of a worm, and then slightly shift a shaft of the steering mechanism with an arm in salon and put under a shaft a support that it did not hang нв wires.


4. Remove a guard of devices and disconnect plug колодки the switch of indexes of turn and light of headlights from plug колодок a bunch of wires.
5. Ослабьте a collar of fastening of a pipe of the top support of a shaft of the steering mechanism also remove it together with the switch of indexes of turn and light of headlights, preliminary having unblocked a shaft of the steering mechanism from the antijoy ride device.
6. Remove an arm 12 (fig. of the Detail of a steering see) fastenings of a shaft of the steering mechanism, preliminary having released it from the ignition switch.
7. Remove a sealant 8 steering mechanisms.
8. Having turned away a bolt of 7 fastenings of a shaft of the steering mechanism to a shaft of a worm, take out a shaft in body salon.
9. Stripper А.47035 выпрессуйте spherical fingers of steering draughts from an aperture сошке.
10. Remove картер the steering mechanism.

The prevention

Removing картер the steering mechanism, note quantity and placing of washers 3 between лонжерогом and картером to establish them on a former place at installation картера. It is necessary for preservation соосности a shaft of the steering mechanism and a shaft of a worm.


11. Installation of the steering mechanism spend to sequences of return to removal.
12. Thus, before definitively to tighten fastening bolts картера the helmsman механизми and an arm of a shaft of the steering mechanism, temporarily put on a shaft a steering wheel, turn a shaft two or three times to the left and to the right. Thus the shaft and other details accept правельное position (самоустанавливаются) thanks to oval apertures on картере and on an arm.

The prevention

It is possible to collect separately a shaft of the steering mechanism with a sealant, an arm, the ignition switch, the switch of indexes of turn and light of headlights, a steering wheel and to establish this knot on the car.



«The previous page
9.2.3. Check and backlash adjustment in gearing of a roller with a worm
The following page»
9.3.1. Removal and installation