VAZ 2101, 2102
1. Specifications
2. Operation and service
3. The engine
4. Fuel system
5. Ignition system
6. Start and gymnastics system
7. Transmission
8. A running gear
9. A steering
10. Brake system
10.1. Features of the device
10.2. Check and adjustment of brakes
10.3. An arm of pedals of coupling and a brake
10.4. The main cylinder
10.5. Forward brakes
10.6. Back brakes
10.7. A regulator of pressure of back brakes
10.7.1. Removal and installation
10.7.2. Dismantling and assemblage
10.7.3. Check of details
10.8. A lay brake
10.9. Possible malfunctions of brakes, their reasons and elimination methods
11. An electric equipment
12. A body
13. Features of repair
14. Appendices


7b94d386







10-7-1-snyatie-i-ustanovka.html

10.7.1. Removal and installation

Details of a drive of a regulator of pressure

1 – a pressure regulator;
2 – an axis of the lever of a drive of a regulator;
3 – грязезащитный a cap;
4 – a lock plate;
5 – a bolt with a spring washer;
6 – the back bridge;
7 – draught of connection of the lever of a drive of a regulator of pressure with an arm of a beam of the back bridge;
8 – a bolt nut;

9 – the plastic plug;
10 – распорная the plug;
11 – a bolt of fastening of draught;
12 – the lever of a drive of a regulator of pressure;
13 – a nut for fastening скобы to a body;
14 – a spring washer;
15 – a flat washer;
16 – скоба fastenings of the lever of a drive of a regulator of pressure;
17 – the rubber plug

PERFORMANCE ORDER
1. Disconnect the lever 12 (fig. of the Detail of a drive of a regulator of pressure see) from draught 7, and then скобу 16 from a body and скобы fastenings of the pipelines going to a regulator of pressure.
2. Disconnect from a body of a detail of a suspension bracket of mufflers and take the pipeline with mufflers aside.
3. Having turned away bolts of fastening of a regulator to an arm and an arm to a body, remove a regulator arm, and then, having lowered a regulator downwards, disconnect from it pipelines.
4. Remove a regulator and disconnect from it the drive lever. Muffle entrance and exhaust outlets of a regulator of pressure and pipelines.
5. Installation of a regulator of pressure spend to sequences, return to removal at the hung out back axis of the car.
6. Before a tightening of bolts of fastening of a regulator, establish on the end of the lever of a drive of a regulator the adaptation 67.7820.9518 (fig. Installation of the adaptation 67.7820.9518 for adjustment of a regulator of pressure of back brakes see).
7. An adaptation core direct upwards against the stop to a body. This most establishes distance 140±5 mm between the end of the lever 4 (fig. the Scheme of installation of a regulator of pressure of back brakes and its adjustment see) and a body longeron.
8. Raise a protective cap 3 (fig. of the Detail of a drive of a regulator of pressure see) and, turning a regulator on fastening bolts, achieve, that the lever end has appeared in easy contact with the regulator piston.
9. Keeping a regulator in this position, tighten to the full bolts of its fastening, then cover with a layer of greasing ДТ-1 an axis 2 and an acting part of the piston. Establish into place a rubber cap 3, having put in it 5-6 г the same greasing.
10. Remove the adaptation 67.7820.9518 and connect the end of the lever to draught 7, preliminary having greased with greasing ДТ-1 of the plug шарнирного connections of draught with the lever.
11. Attach to a body pipelines of system of release of gases.
12. Then pump over brakes for removal of air from a drive of back brakes.

«The previous page
10.7. A regulator of pressure of back brakes
The following page»
10.7.2. Dismantling and assemblage